![]() |
![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() |
FQ系列光纤传感器 |
||
感应距离 | 因纤维材料不同而异 | |
功能: | 可设定 | |
定时器 | ||
可编程 | ||
外壳尺寸: | 30x65x10mm |
FQ系列光纤传感器规格 | ||
类型 | NPN输出 | PNP输出 |
工作电压 | 10至30V DC 涟波 P-P 10% 或更少 | |
功耗 | 普通操作: ≤960mW (24V工作电压时电流耗量 ≤40mA) ECO模式: ≤960mW (24V工作电压时电流耗量 ≤25mA) |
|
输出方式 | NPN 晶体管集电极开路输出 最大电流:100mA 工作电压:≤ 30V DC ·剩余电压:≤1.5V 于100mA |
PNP 晶体管集电极开路输出 最大源电流:100mA 工作电压:≤30V DC ·剩余电压:≤1.5V 于 100mA |
输出操作 | 可设置成Light-ON 或 Dark-ON | |
短路保护 | 有 | |
响应时间 | ≤150μs , ≤250s , ≤2.0ms ,可选择 | |
显示 |
4 位数字 LED 显示 | |
感应设置 |
2 level teach-in /Limit teach-in/ Manual adjustment | |
感应距离可调功能 |
可调 | |
定时功能 |
集成可变的 ON-delay/OFF-delay/ONE- SHOT 定时器, 可设置成开或关 | |
防干涉功能 |
有 | |
工作环境温度 | -10 °C 至 +55 °C | |
工作环境湿度 | 35 有 85% RH, 存贮: 35 有 85% RH | |
光源 | 红 LED( 已调整) | |
材质 | 外壳: 抗热 ABS, 透明外套: Polycarbonate, 开关: Acrylic | |
重量 | 约 20g |
安装 | |
How to mount the amplifier | |
① Fit the rear part of the mounting section of the amplifier on a 35mm width DIN rail. | ![]() |
② Press down the front part of the mounting section of the amplifier on the 35mm width DIN rail. |
|
How to remove the amplifier | |
① Push the amplifier forward. | ![]() |
② Lift up the front part of the amplifier to remove it. Note: Take care that if the front part is lifted without pushing the amplifier forward, the hook on the rear portion of the mounting section is likely to break. | |
How to connect the amplifier | |
① Snap the fiber lock lever down.. | ![]() |
② Insert the fiber cables slowly into the inlets until they stop.(Note1) | |
③ Return the fiber lock lever to the original position till it stops. |
FQ系列光纤传感器接线图 |
|
|
构件描述 |
![]() |
FQ系列光纤传感器尺寸图(mm) | ||
Amplifier(FQ-301P/N...)
|
SKY-E @ Copyright (C) 2009 All Rights Reserved |
电话联系:86 0574 88335695.传真:86 0574 88335636 ...在线联系: |